Important Plumber Guide for Bathtub Installation
Important Plumber Guide for Bathtub Installation
Blog Article
We've encountered this great article pertaining to Installing A Bathtub below on the web and accepted it made good sense to share it with you on my blog.
Setting up a bathtub isn't specifically brain surgery, however it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old tub with a new one is additionally a moderately tough project. If the old tub is readily accessible, the task can move rapidly; if you have to open up a wall to remove the old bathtub and position the new bathtub, the job is much harder. In either situation, the job is within a home handyman's skills, although you will need a helper to vacate the old tub and also set in the new one. Make certain you have qualified yourself for the job and fit trying it. As opposed to working with a contractor to take control of a halfway-completed job, it is better to take into consideration utilizing one before you start. Opportunities are you might need a specialist plumber to make tube connections.
This short article will certainly help you mount a new bath tub in your restroom if you have actually already bought a brand-new tub and also don't require to change the plan of your previous water pipes.
Your tools as well as product checklist need to make up the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly troublesome as a result of the restricted access that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a towel ready for the remaining water that will originate from the pipelines. As soon as the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Safeguard the faucet in place with the supplier provided backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The former type should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Utilizing the two wooden boards under its feet, put the bathtub in the needed placement. The wood boards are helpful in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bath tub up until the spirit level reads level.
To install faucets, fit all-time low of the furthest flexible faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Switch on the water supply and also examine all joints and brand-new pipework for leaks and also tighten them if required. Fill up the bathtub and also examine the overflow outlet and the normal outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the bathtub needs to wait till the bath tub has been used at the very least once as this will settle it right into its final setting.
Planning for the Installation
Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets device to stop stress on the bath tub.
Fit the flexible tap ports to the bottom of the two faucets using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its final position.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, causing the water to penetrate the wall in between the bathroom and also the tiling, resulting in problems with moisture as well as possible leaks to the ceiling below.
You can select from a range of coloured sealers to blend in your components and installations. They are marketed in tubes as well as cartridges, and are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bath tub with water before securing, to enable the movement experienced when the tub remains in use. The sealant can fracture rather early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also easily offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading about How to Install a Bathtub? Post feedback down the page. We would be delighted to see your suggestions about this blog. We are looking forward to see you back again soon. Sharing is caring. You won't know, you may just be doing someone a favor. Thanks a lot for going through it.
Get the best, call! Report this page